![]() ![]() It is recommended to use a siphon or diaphragm seal with the gauge in such a situation with very high or low temperatures.Temperature: It is ideal to understand the operating temperature limit and select the gauge that can withstand both high and low-temperature extremes.Depending upon the type of application, the pressure usually ranges from 0 to 250 psi. Pressure Unit: The general pressure unit for the air compressor gauge is psi.The operating pressure range should be limited to 75% of the gauge range. Pressure Range: The air compressor gauge should have a range twice the working pressure for maximum safety and accuracy.However, for extreme applications and different media or environmental conditions, see our chemical compatibility chart for more detail. Material: Most air compressor pressure gauges have stainless steel housing with FKM as the seal material.When selecting a gauge diameter, it is also important to note the readability, space limitations, and acceptable margin of error offered by each gauge depending upon your application. Commonly, the range from 1 to 16 (25 mm to 406 mm) is widely available. Gauge Diameter: Depending upon your requirement, you can select the dial size from a wide range of diameters.However, for unique applications, a diaphragm or bellows pressure gauge can be used. Gauge Type: Typically for air compressors, a bourdon tube pressure gauge is used. ![]() Watch the below Youtube video for more information: #INGERSOLL RAM PRESSURE GAUGE INSTALL#The readings from these gauges are essential in understanding the air pressure intensity inside the tank. Should the pressure not be easy to read due to pressure fluctuations or vibrations, it is recommended to install a snubber for a pressure gauge. A regulator knob can be used to increase or decrease the air pressure setting. Regulator Air Gauge: The regulator pressure gauge displays the pressure the user has optimized for the air tool application.This gauge is essential in identifying if there is enough air available or if the air compressor is shutting off at the correct cut-off pressure. Tank Air Gauge: This pressure gauge displays the pressure in the tank as the compressor pumps the air to pressurize it.This pressure is the amount of pressure received by the air tool. The other pressure gauge is the pressure gauge that indicates the pressure setting at the regulator. One of them is the pressure gauge to indicate the air pressure in the tank. Typically, air compressors used for industrial applications have two pressure gauges to indicate the PSI level of the two key stages in the pressurization process. To learn more about the inner workings of pressure gauges, read our pressure gauge informational article. ![]() It is advantageous to know the pressure created by the air compressor to not over-pressure the system and know it’s at the application’s specifications. An air compressor gauge is a device used to display the pressure of compressed air in the system. The motor typically requires electricity or internal combustion to operate. The OEM switch from Ingersoll Rand is rated for a higher amp draw and is much heavier duty compared to others.An air compressor is a pneumatic device that creates pressurized air for a system. #INGERSOLL RAM PRESSURE GAUGE FULL#Plenty of aftermarket switches are sold online, but many of them are not rated for the full load amp draw of the compressor and will cause pre-mature wear to the switch. This is an OEM switch from Ingersoll Rand. Please call or email our parts department if you need help sourcing a check valve. If you find your pressure switch is constantly leaking out of the unloader line, you should consider changing the check valve instead. This results from the contacts being welded together over time. Typically the pressure switch needs to be replaced if the compressor does not turn on at the lower setpoint or does not turn off at the upper pressure setpoint (causing the safety valve the blow off). The 23474661 utilizes a single threaded port on the bottom and includes an on/off switch. The pre-set cut-in pressure is 95psi and the cut-off pressure is 125psi providing a 30 psi pressure differential. The unloader valve is swivel based and can be adjusted to fit the unloader tube if needed. The pressure switch turns the compressor on when it hits the lower pressure setpoint and kicks the compressor off when the upper setpoint is reached. Ingersoll Rand SS3 / SS5 Pressure Switch Replacement – 23474661 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |